Leading 10 common forklift mishaps ， forklift operation must pay attention to these issues ！.

Don't ignore the forklift at the office. If the procedure is bad, there will certainly be severe crashes in mins, and there are lots of crashes including forklifts.

Case 1: The forklift cargo obstructed the driver's sight, and the person ahead can not be located, resulting in a moving mishap.
Case 2: In order to preserve the balance of the forklift when raising heavy goods, the staff members used their body weight as the counterweight, which practically created casualties.
Case 3: The width of the forklift freight surpasses the allowed size of the route and holds on the roadside rack, which almost triggers an mishap.
Case 4: Forklift is speeding up and rolls over during a turn.
Instance 5: The forklift driver did not discover the pedestrian, and the pedestrian did not notice the forklift.
Case 6: The forklift lifts the workers illegally, the forklift motorist does not use the seat belt, the forklift lifter drops and the vehicle driver is crushed when the forklift rolls over.
Case 7: The forklift vehicle driver did not put on a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift operation need to take notice of these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after confirming that there are no obstacles that prevent the security of driving, honk the horn first and after that begin.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale need to be safe prior to starting.
3. When the forklift begins with a load, the motorist needs to first verify that the lots is steady and reliable.
4. The start must be slow-moving and steady.

Driving.
1. When driving, the height between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the mast ought to be slanted backward. .
2. Do not raise the fork too high when driving. When entering and leaving the job site or while driving, take care that there will certainly be no obstacles overhead. When the lots is traveling, the fork should not be elevated too expensive, which will certainly influence the security of the forklift. .
3. After dumping, the fork should be decreased to the typical driving setting prior to driving. .
4. When turning, if there are pedestrians or vehicles nearby, the driving signal ought to be issued initially. High-speed doglegs are forbidden. High-speed doglegs will certainly cause the car to shed side security and tip over. .
5. When the forklift is downhill, it is strictly restricted to shut off the flame and slide, and it is restricted to brake instantly while driving with tons unless there are special scenarios.
6. When the forklift is running, it should obey the traffic rules in the manufacturing facility and should maintain a specific safety range from the car ahead. .
7. When the forklift is running, the lots should remain in the lowest setting that does not prevent the driving, and the gantry ought to be properly slanted back. The tons will not be increased other than when stacking or filling. .
8. The elevation of the load need to not block the motorist's sight. In special circumstances, when the product impacts the forward vision, drive at a reduced speed when reversing.
9. It is restricted to turn on the ramp, neither to drive throughout the ramp. .
10. The safe driving rate of the forklift in the factory area is 5 km/h, and it needs to drive securely at a reduced rate when entering the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is forbidden for personnel to depend on the fork to hold items and play a stabilizing role. .
12. If troubles are located, they will certainly be fixed and reported in a prompt manner, and they will never operate with ailments or hide them.

filling and discharging.
1. When fork-loading products, the distance between the two forks ought to be adjusted as needed to make the load of the two forks well balanced and not manipulated, and one side of the thing should protest the shelf. .
2. It is prohibited to collaborate with a single fork or make use of a fork top or draw. In special conditions, safety and security indication should be set up to remind surrounding pedestrians. .
3. In the process of packing and discharging things, the forklift should be stopped with the brake. .
4. The rate of the car must be slow and consistent. Beware not to roll the wheels on the dunnage, so as not to extend the rolled things and harm individuals. .
5. When making use of a fork to fork the goods, the fork should be as deep as possible under the load, and it should be kept in mind that the fork idea should not touch other goods or objects. The tons should be supported with minimal back tilt of the gantry to ensure that the lots does not slide backwards. The pole can be slanted ahead somewhat when the lots is lowered to enable simple positioning of the lots and extraction of the forks. .
6. It is restricted to fork products at high speed and ram hard items with the fork head. .
7. When the forklift is working, it is restricted for people to stand around the fork, so as to prevent the collapse of the goods and harm individuals. .
8. Straining is prohibited, and it is prohibited to use forks to lift personnel to engage in high-altitude operations to stay clear of high-altitude falling accidents. .
9. It is not permitted to make use of the brake inertia to slide, place, round or roll items. .
10. It is not allowed to use forks to select, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you should unload the goods or reduced the fork framework.
2. Draw the hand brake take care of to dead or depress the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique scenarios, such as the motorist does not leave the lorry's line of sight and does not go beyond 1 min).
4. Stand-on Electric Pallet Stacker Get rid of the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the appearance should be inspected, and gas, lubricating oil and air conditioning water should be added.
2. Inspect the safety and security performance of starting, running and braking.
3. Examine whether the lights and horn signals are complete Stand-on Electric Pallet Stacker and efficient.
4. Throughout the operation of the forklift, check whether the pressure and temperature are typical.
5. After the forklift is running, the exterior leak should also be examined and the seals should be replaced in time.

Forklift Safety Operation Specifications.
1. You should check before leaving the cars and truck;.
2. When you come across a person in front of you throughout driving, you should send a signal at a distance of 5 m;.
3. The driving rate in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the nadir of the freight should be 0.3 m ~ 0.4 m above the ground;.
5. The turning ought to not be also sharp to prevent the propensity of " cost-free turning";.
6. Running up and down the slope must be slow-moving and consistent, and no activating the slope is enabled.
7. Do not drive across the gradient. When the slope is greater than 10%, the automobile must be driven in reverse when worsening;.
8. When the forklift personnel carry the goods and progress, if they run into big or heavy products and go to the chauffeur's line of sight, they ought to take the reversing workout
.
The "Eight Prohibitions" need to be adhered to in the operation.
1. Solitary fork operation is not enabled.
2. It is not allowed to lift the goods for far away driving.
3. It is not permitted to get the goods by handing over the pallet with the fork.
4. It is not enabled to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not permitted to utilize inertia pressure to pick up the goods.
6. It is not enabled to make use of stopping force to exile round or easy-to-roll items.
7. It is not allowed to bring people to deal with the pallet or fork, and it is strictly restricted to stand under the fork after the fork is increased.
8. Do not drive laterally on slopes
.
Parking is not allowed under the list below conditions.
1. Curves, narrow roadways, train crossings;.
2. Sections with a longitudinal incline above 5%.
3. When there is an challenge on one side of the road, the opposite side of the section with the exact same length as the barrier ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844